Forklift Chains

Forklift Chain - The life of the lift truck lift chains can be extended with correct care and maintenance. Lubricating correctly is an excellent method to be able to prolong the capability of this particular forklift component. It is essential to apply oil occasionally with a brush or other lube application tool. The volume and frequency of oil application must be sufficient so as to stop whatever rust discoloration of oil within the joints. This reddish brown discoloration generally signals that the lift chains have not been correctly lubricated. If this particular situation has happened, it is really important to lubricate the lift chains as soon as possible.

It is typical for a few metal to metal contact to occur throughout lift chain operation. This could cause components to wear out in time. The industry standard considers a lift chain to be worn out when three percent elongation has occurred. In order to avoid the scary likelihood of a disastrous lift chain failure from occurring, the manufacturer very much suggests that the lift chain be replaced before it reaches 3 percent elongation. The lift chain lengthens due to progressive joint wear that elongates the chain pitch. This elongation is capable of being measured by placing a certain number of pitches under tension.

So as to ensure correct lift chain maintenance, another factor to consider is to check the clevis pins on the lift chain for signs of wearing. Lift chains are put together so that the clevis pins have their tapered faces lined up with each other. Normally, rotation of the clevis pins is frequently caused by shock loading. Shock loading takes place when the chain is loose and then suddenly a load is applied. This causes the chain to go through a shock as it 'snaps' under the load tension. Without the good lubrication, in this particular situation, the pins can rotate in the chain's link. If this scenario occurs, the lift chains should be replaced instantly. It is imperative to always replace the lift chains in pairs in order to ensure even wear.


Click to Download the pdf

Forklift Parts

Parts for Diesel Boom Lift

Diesel Boom Lift Parts - Also known as aerial work platforms, boom lifts comprise a platform or bucket mechanism which is attached to a hydraulic hoisting system. This kind of aerial work platform is usually found mounted on a flat-back pickup van, likewise referred to as a "Self Drive." Boom lifts are likewise obtainable on a self-moving platform, or on...

More

---

Clark Forklift Attachment

Clark Forklift Attachments - At present, there are at least 350,000 Clark lift trucks performing worldwide, and in excess of 250,000 in commission in North America alone. With five major lines across the world, Clark is proud to be one of the most expansive organizations in the industry. Heavy duty vehicles ranging from 1,500lb to 18,000lb capacities, duel fuel, gasoline,...

More

---

Forklift Starter

Forklift Starters - A starter motors today is normally a permanent-magnet composition or a series-parallel wound direct current electrical motor together with a starter solenoid installed on it. When current from the starting battery is applied to the solenoid, basically through a key-operated switch, the solenoid engages a lever which pushes out the drive pinion which is situated on the...

More

---

Concrete Hopper

Concrete Hopper - The self-dumping hopper accessory could automatically start to both dump and release when the bumper release contacts the side of a dumpster. After unloading is finished, the hopper is able to return to original locked and upright position. This piece of equipment also comes together with a cable that allows operation from the seat of the forklift...

More

---

Remanufactured Forklift Part

Remanufactured Forklift Parts - Lift trucks are really expensive pieces of machinery. A five thousand pound new electric model can cost between $18,000 to $25,000 and several thousands of dollars more will be needed for a battery and a battery charger. The same internal combustion forklift of the same lift capacity would cost a little less and the diesel models...

More

---

Walkie Stacker Part

Walkie Stacker Parts - Pallet stackers are a kind of pallet jack that can be used to stack, transfer and haul cargo positioned on a pallet that are far too heavy for physical lifting. Generally these mechanisms are employed to load and unload cargo from trucks and to transport pallets from one location to another within a warehouse of storeroom...

More

---

Fuel Regulator for Forklift

Forklift Fuel Regulators - Where automatic control is concerned, a regulator is a tool which functions by maintaining a specific characteristic. It carries out the activity of managing or maintaining a range of values inside a machine. The measurable property of a tool is closely managed by an advanced set value or particular circumstances. The measurable property could even be...

More

---

Lifting Hook

Lifting Hooks - A lifting hook is a tool designed for carrying and grabbing things in conjunction with a crane or hoist. The lifting hook is usually outfitted along with a safety latch. The latch prevents the disengagement of the chain, lifting wire rope sling, or rope to which the load is attached.

More

---